Showing 2065–2076 of 2445 results
MCP4922 12-Bit Dual Voltage Digital to Analog Converter (DAC) with SPI Interface IC DIP-14 Package
The MCP4922 devices are dual 8-bit, 10-bit, and 12-bit buffered voltage output Digital-to-Analog Converters (DACs), respectively. The devices operate from a single 2.7V to 5.5V supply with SPI compatible Serial Peripheral Interface. The user can configure the full-scale range of the device to be VREF or 2 * VREF by setting the Gain Selection Option bit (gain of 1 of 2). The user can shut down both DAC channels by using SHDN pin or shut down the DAC channel individually by setting the Configuration register bits. In Shutdown mode, most of the internal circuits in the shutdown channel are turned off for power savings and the output amplifier is configured to present a known high resistance output load (500 k???typical?.
MCP73831 IC – (SMD SOT-23 Package) – Li-ion Battery Charger IC
The MCP73831 devices are highly advanced linear charge management controllers for use in spacelimited, cost-sensitive applications. The MCP73831 are available in an 8-Lead, 2 mm x 3 mm DFN package or a 5-Lead, SOT-23 package. Along with their small physical size, the low number of external components required make the MCP73831 ideally suited for portable applications. For applications charging from a USB port, the MCP73831 adhere to all the specifications governing the USB power bus. The MCP73831 employ a constant-current/constant voltage charge algorithm with selectable preconditioning and charge termination. The constant voltage regulation is fixed with four available options: 4.20V, 4.35V, 4.40V or 4.50V, to accommodate new, emerging battery charging requirements. The constant current value is set with one external resistor. The MCP73831 devices limit the charge current based on die temperature during high power or high ambient conditions. This thermal regulation optimizes the charge cycle time while maintaining device reliability. Several options are available for the preconditioning threshold, preconditioning current value, charge termination value and automatic recharge threshold. The preconditioning value and charge termination value are set as a ratio or percentage of the programmed constant current value. Preconditioning can be disabled The MCP73831 devices are fully specified over the ambient temperature range of -40?C to +85?C.
MCT2E Optocoupler Phototransistor IC DIP-6 Package
The MCTE is an Industry Standard Single Channel Photo transistor. Each optocoupler consists of gallium arsenide infrared LED and a silicon NPN photo transistor. These couplers are Underwriters Laboratories (UL) listed to comply with a 5300 VRMS isolation test voltage. This isolation performance is accomplished through double molding isolation manufacturing process. Compliance to DIN EN 60747-5-2(VDE0884)/ DIN EN 60747-5-5 pending partial discharge isolation specification is available for these families by ordering option 1. These isolation processes and the ISO 9001 quality program results in the highest isolation performance available for a commercial plastic photo transistor optocoupler. The devices are available in lead formed configuration suitable for surface mounting and are available either on tape and reel, or in standard tube shipping containers.
MCT6 IC – Dual Phototransistor Optocoupler IC
MCT62 IC – Dual Channel Phototransistor Optocoupler IC
Mechanic XG-50 35gm SMD Solder Paste
This is solder paste for soldering small SMD components in reflow oven or with hot air soldering station. comes in a small container for prototyping or repairing job. This pack is right amount of solder paste for most of the hobby projects. This paste is replacement of solder wire used in Through hole soldering, some times solder flux is referred as solder paste. This solder paste comes in a special container, when it is sealed, it can survive for 6 months. If you open the container and want to store rest of the paste for future use make sure it is tight and place it in a plastic zipper pouch and place it in the refrigerator.
Mechanic XG-50 50gm SMD Solder Paste
This is solder paste for soldering small SMD components in reflow oven or with hot air soldering station. comes in a small container for prototyping or repairing job. This pack is right amount of solder paste for most of the hobby projects. This paste is replacement of solder wire used in Through hole soldering, some times solder flux is referred as solder paste. This solder paste comes in a special container, when it is sealed, it can survive for 6 months. If you open the container and want to store rest of the paste for future use make sure it is tight and place it in a plastic zipper pouch and place it in the refrigerator.
MG16126-A Helping Hand for PCB with Multifunctional Magnifier (Magnifying Glass) and Soldering Iron Stand with LED Light
MIC29302 – (SMD TO-263 Package) – LDO Voltage Regulator
The MIC29302 are high current, high accuracy, low dropout voltage regulators. Using Microchip?s proprietary Super ?eta PNP process with a PNP pass element, these regulators feature 350 mV to 425 mV (full load) typical dropout voltages and very low ground current. Designed for high current loads, these devices also find applications in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes. The MIC29302 are fully protected against over current faults, reversed input polarity, reversed lead insertion, over temperature operation, and positive and negative transient voltage spikes. Five pin fixed-voltage versions feature logic level ON/OFF control and an error flag that signals whenever the output falls out of regulation. Flagged states include low input voltage (dropout), output current limit, over temperature shutdown, and extremely high voltage spikes on the input. The MIC29302 are available in 3-pin and 5-pin TO-220 and surface mount TO-263 (D2Pak) packages.
MIC4576-5BU IC – Step Down Regulator IC
The MIC4576 is a series of easy-to-use fixed and adjustable BiCMOS step-down (buck) switch-mode voltage regulators. The 200 kHz MIC4576 duplicates the pinout and function of the 52 kHz LM2576. The higher switching frequency may allow up to a 2:1 reduction in output filter inductor size. The MIC4576 is available in 3.3V, and 5V fixed output versions or a 1.23V to 33V adjustable output version. Both versions are capable of driving a 3A load with excellent line and load regulation. The feedback voltage is guaranteed to ?2% tolerance for adjustable versions, and the output voltage is guaranteed to ?3% for fixed versions, within specified voltages and load conditions. The oscillator frequency is guaranteed to ?10%. In Shutdown mode, the regulator draws less than 200 ?A shutdown current. The regulator performs cycle-by-cycle current limiting and thermal shutdown for protection under fault conditions. This series of simple switch-mode regulators requires a minimum number of external components and can operate using a standard series of inductors. Frequency compensation is provided internally. The MIC4576 is available in TO-220 (T) and TO-263 (U) packages for the industrial temperature range.
Mix Ceramic Capacitor Box – 20 Values (5 Piece Each Value)
Boards & Modules
ARM Microcontroller
AVR Microcontroller Board
Arduino boards
Advance Development Boards
8051 Development Board
Audio Amplifier Module
Current & Volatage Sensor
Breakout Board
Flame Sensors
Force Sensor
Gas Sensors
Hall Effect Sensor
Humidity & Temperature Sensor
LED Module
PIR Sensor
Pressure Sensors
Proximity Sensor
Relay Module
Real Time Clock (RTC) Module
Touch Sensor
Ultrasonic Sensor
Water Level & Water Flow Sensor
Weighing Scale Sensor
Ai Thinker ESp Wifi Module
Pic Devlopment Board & programmer
Led lights & Strips
PCBs & Breadboard
Potentiometer
Power Transistors
Resistor & Smd & inductor
Switches
Aluminium Heat Sink
Buzzer & Speaker
capacitor
Crystal Oscillators
Doides
Electric Fuses
ICs & Dips
Power supply module
Transformer
Relay Module
Kits
Magnet
RF Connectors
PCT and DC Connectors
Wires & Heat Shrink
FFC, FPC, Berg connectors
Nextion
Segment
Seedstudio
Waveshare
E Bike Batteries
E bike Battery Case
E bike Connectors
E bike Display
E bike Kit
E bike Motors & Controllers
Electronics Accessories
Mechanical Accessories
Display
Cameras