Showing 2761–2772 of 3753 results
MAX7219 Dot Matrix 4 in 1 Display Module
MAX7219 4-in-1 Display Dot Matrix Module is an integrated serial input/output common-cathode display driver, it connects the microprocessor 7-segment digital LED display with 8 digits, you can also connect a bar graph display or 64 independent LED. Thereon including a B-type BCD encoder chip, multi-channel scanning loop segment word driver, but also a static RAM 8 x 8 for storing each data. Only one external register is used to set the segment current of each LED.
MAX7219 IC – (SMD Package) – 8-Digit LED Display Driver IC
MAX7221 IC – (SMD Package) – 8-Digit LED Display Driver IC
MB102 Breadboard Power Supply Module 3.3V/5V
Use this power regulation module to provide 5V and 3V3 power supply to your breadboard based project.This power supply board is designed to plug into a Breadboard panel with 2 power Distribution strips. The module can be powered by a USB port or an external power supply 7-12V. The module has two independent power lines, which can be set to output voltage of 5V or 3.3V, or completely remove power from the line. The module has ON / OFF switch to turn on and off module. It comes with reverse polarity and short circuit protections, which greatly helps during building and testing circuits on the breadboard.
MBR20100CT 100V 20A Dual High Voltage Schottky Rectifier
MBR20200CT 200V 20A Schottky Rectifier – Plastic Package
The MRB20200CT using Schottky Barrier technology with a platinum barrier metal. This state?of?the?art device is designed for use in high frequency switching power supplies and converters with up to 48 volt outputs. They block up to 200 volts and offer improved Schottky performance at frequencies from 250 kHz to 5.0 MHz.
MC-38 Wired Door Window Sensor Magnetic Switch Home Alarm System
MC-38 Wired Door Window Sensor Magnetic Switch Home Alarm System can be used as a door or window security system. It produces the signal when moved away from each other which can be fed to the microcontroller to perform the desired action as per requirement.
This sensor suitable to use for trigger alarm or ON/OFF light inside a cupboard sliding door. This wired sensor is trigger by the magnet. When the magnet is closed by, the circuit is closed or open if the magnet far from the sensor.
MC10158 Quad 2-Input Multiplexer IC DIP-16 Package
MC1408 8-Bit Multiplying Digital to Analog D/A Converter (DAC) IC DIP-16 Package
MC14490 Hex Contact Bounce Eliminator IC DIP-16 Package
The MC14490 is constructed with complementary MOS enhancement mode devices, and is used for the elimination of extraneous level changes that result when interfacing with mechanical contacts. The digital contact bounce eliminator circuit takes an input signal from a bouncing contact and generates a clean digital signal four clock periods after the input has stabilized. The bounce eliminator circuit will remove bounce on both the ?make? and the ?break? of a contact closure. The clock for operation of the MC14490 is derived from an internal R?C oscillator which requires only an external capacitor to adjust for the desired operating frequency (bounce delay). The clock may also be driven from an external clock source or the oscillator of another MC14490.
MC1489 IC – (SMD Package) – Quadruple Line Receivers IC
These devices are monolithic low-power Schottky quadruple line receivers designed to satisfy there requirements of the standard interface between data-terminal equipment and data-communication equipment as defined by TIA / EIA-232-F. separate response-control (CONT) terminal is provided for each receiver. A resistor or a resistor and bias-voltage source can be connected between this terminal and ground to shift the in put levels. An external capacitor can be connected between this terminal and ground to provide input noise filtering. The SN55189 and SN55189A are characterized for operation over the full military temperature range of ? 55?C to 125?C. The MC1489,MC1489A, SN75189, and SN75189A are characterized for operation from 0?C to 70?C
MC1489 Quadruple Line Receivers IC DIP-14 Package
These devices are monolithic low-power Schottky quadruple line receivers designed to satisfy there requirements of the standard interface between data-terminal equipment and data-communication equipment as defined by TIA / EIA-232-F. separate response-control (CONT) terminal is provided for each receiver. A resistor or a resistor and bias-voltage source can be connected between this terminal and ground to shift the in put levels. An external capacitor can be connected between this terminal and ground to provide input noise filtering. The SN55189 and SN55189A are characterized for operation over the full military temperature range of ? 55?C to 125?C. The MC1489,MC1489A, SN75189, and SN75189A are characterized for operation from 0?C to 70?C
Boards & Modules
ARM Microcontroller
AVR Microcontroller Board
Arduino boards
Advance Development Boards
8051 Development Board
Audio Amplifier Module
Current & Volatage Sensor
Breakout Board
Flame Sensors
Force Sensor
Gas Sensors
Hall Effect Sensor
Humidity & Temperature Sensor
LED Module
PIR Sensor
Pressure Sensors
Proximity Sensor
Relay Module
Real Time Clock (RTC) Module
Touch Sensor
Ultrasonic Sensor
Water Level & Water Flow Sensor
Weighing Scale Sensor
Ai Thinker ESp Wifi Module
Pic Devlopment Board & programmer
Led lights & Strips
PCBs & Breadboard
Potentiometer
Power Transistors
Resistor & Smd & inductor
Switches
Aluminium Heat Sink
Buzzer & Speaker
capacitor
Crystal Oscillators
Doides
Electric Fuses
ICs & Dips
Power supply module
Transformer
Relay Module
Kits
Magnet
RF Connectors
PCT and DC Connectors
Wires & Heat Shrink
FFC, FPC, Berg connectors
Nextion
Segment
Seedstudio
Waveshare
E Bike Batteries
E bike Battery Case
E bike Connectors
E bike Display
E bike Kit
E bike Motors & Controllers
Electronics Accessories
Mechanical Accessories
Display
Cameras