Showing 3529–3540 of 3753 results
TC4420 IC – 6A High-speed MOSFET Driver IC
The TC4420 is 6A (peak), single-output MOSFET drivers. The TC4420 is a non-inverting driver. These drivers are fabricated in CMOS for lower power and more efficient operation versus bipolar drivers. Both devices have TTL/CMOS compatible inputs that can be driven as high as VDD + 0.3V or as low as ?5V without upset or damage to the device. This eliminates the need for external level-shifting circuitry and its associated cost and size. The output swing is rail-to-rail, ensuring better drive voltage margin, especially during power-up/power-down sequencing. Propagational delay time is only 55 ns (typ.) and the output rise and fall times are only 25 ns (typ.) into 2500 pF across the usable power supply range. Unlike other drivers, the TC4420 is virtually latch-up proof. They replace three or more discrete components, saving PCB area, parts and improving overall system reliability.
TC4427 IC – (SMD Package) – Power MOSFET Driver IC
TC4427 IC – Power MOSFET Driver IC
The TC4427 is improved versions of the earlier TC4427 family of MOSFET drivers. The TC4427 devices have matched rise and fall times when charging and discharging the gate of a MOSFET. These devices are highly latch-up resistant under any conditions within their power and voltage ratings. They are not subject to damage when up to 5V of noise spiking (of either polarity) occurs on the ground pin. They can accept, without damage or logic upset, up to 500 mA of reverse current (of either polarity) being forced back into their outputs. All terminals are fully protected against Electrostatic Discharge (ESD) up to 2.0 kV. The TC4427 MOSFET drivers can easily charge/discharge 1000 pF gate capacitances in under 30 ns. These devices provide low enough impedances in both the On and Off states to ensure the MOSFET?s intended state is not affected, even by large transients. Other compatible drivers are the TC4427A family of devices. The TC4427A devices have matched leading and falling edge input-to-output delay times, in addition to the matched rise and fall times of the TC4427 devices.
TC7660 IC – Charge Pump DC to DC Voltage Converter IC
The TC7660 device is a pin-compatible replacement for the industry standard 7660 charge pump voltage converter. It converts a +1.5V to +10V input to a corresponding -1.5V to -10V output using only two low-cost capacitors, eliminating inductors and their associated cost, size and electromagnetic interference (EMI). The on-board oscillator operates at a nominal frequency of 10 kHz. Operation below 10 kHz (for lower supply current applications) is possible by connecting an external capacitor from OSC to ground. The TC7660 is available in 8-Pin PDIP, 8-Pin Small Outline (SOIC) and 8-Pin CERDIP packages in commercial and extended temperature ranges.
TC7662 IC – Charge Pump DC to DC Voltage Converter IC
The TC7662A is a pin-compatible upgrade to the industry standard TC7660 charge pump voltage converter. It converts a +3V to +18V input to a corresponding -3V to -18V output using only two low cost capacitors, eliminating inductors and their associated cost, size and EMI. In addition to a wider power supply input range (3V to 18V versus 1.5V to 10V for the TC7660), the TC7662A can source output currents as high as 40mA. The on-board oscillator operates at a nominal frequency of 12kHz. Operation below 12kHz (for lower supply current applications) is also possible by connecting an external capacitor from OSC to ground. The TC7662A directly is recommended for designs requiring greater output current and/or lower input/ output voltage drop. It is available in 8-pin PDIP and CERDIP packages in commercial and extended temperature ranges.
TCA965B IC – Window Discriminator IC
The window discriminator compares an input voltage to a defined voltage window. The digital outputs show whether the input voltage is below, within or above this window. The TCA 965 B window discriminator is especially suitable as a tracking or compensating controller with a dead band in control engineering and for the selection of DC voltages within a certain tolerance of the required setpoint value in measurement engineering. When it is used as a Schmitt trigger, switching frequencies up to a typical value of 50 kHz are possible.
TCS3200 TCS230 Color Sensor Module
Color Sensor, based on TCS3200, is a complete color detector capable of detecting static color. The output of the sensor is a square wave with frequency directly proportional to incident light intensity. It also supports fill light by on board LEDs. It includes a TAOS TCS3200 RGB sensor chip and 4 white LEDs. The TCS3200 can detect and measure a nearly limitless range of visible colors. Applications include test strip reading, sorting by color, ambient light sensing and calibration, and color matching, to name just a few.
The TCS3200 Color Sensor board makes it very easy to sense and record the light intensity of the general red, green, and blue spectrums of visible light while rejecting IR from light sources. You can then use these color sensor readings for the purposes of logging and finding patterns, or creatively calculate and make control decisions in your electronic projects.
The TCS3200 GBB Color Sensor For Arduino has an array of photo detectors, each with either a red, green, or blue filter, or no filter (clear). The filters of each color are distributed evenly throughout the array to eliminate location bias among the colors. Internal to the device is an oscillator which produces a square-wave output whose frequency is proportional to the intensity of the chosen color.
TD62064AFG IC – (SMD Package) – 4-Channel High-Current Darlington Sink Driver IC
TD62083 IC – (SMD Package) – 8-Channel Darlington Sink Driver IC
TDA0161DP IC – Proximity Detector IC for Metal Detection
These monolithic integrated circuits are designed for metallic body detection by sensing variations in high frequency Eddy current losses. Using an externally-tuned circuit, they act as oscillators. The output signal level is altered by an approaching metallic object. The output signal is determined by supply current changes. Independent of supply voltage, this current is high or low, according to the presence or absence of a closely located metallic object.
TDA2002 8W Hi-Fi Audio Power Amplifier IC TO-220-5 Package
TDA2030 18W Hi-Fi Audio Power Amplifier IC TO-220-5 Package
The TDA2030 is a monolithic IC in a Pentawatt package intended for use as a low-frequency class-AB amplifier. With VS max = 44 V it is particularly suited for more reliable applications without regulated supply and for 35 W driver circuits using low-cost complementary pairs. The TDA2030 provides high output current and has very low harmonic and crossover distortion. The device incorporates a short-circuit protection system comprising an arrangement for automatically limiting the dissipated power so as to keep the operating point of the output transistors within their safe operating range. A conventional thermal shutdown system is also included.
Boards & Modules
ARM Microcontroller
AVR Microcontroller Board
Arduino boards
Advance Development Boards
8051 Development Board
Audio Amplifier Module
Current & Volatage Sensor
Breakout Board
Flame Sensors
Force Sensor
Gas Sensors
Hall Effect Sensor
Humidity & Temperature Sensor
LED Module
PIR Sensor
Pressure Sensors
Proximity Sensor
Relay Module
Real Time Clock (RTC) Module
Touch Sensor
Ultrasonic Sensor
Water Level & Water Flow Sensor
Weighing Scale Sensor
Ai Thinker ESp Wifi Module
Pic Devlopment Board & programmer
Led lights & Strips
PCBs & Breadboard
Potentiometer
Power Transistors
Resistor & Smd & inductor
Switches
Aluminium Heat Sink
Buzzer & Speaker
capacitor
Crystal Oscillators
Doides
Electric Fuses
ICs & Dips
Power supply module
Transformer
Relay Module
Kits
Magnet
RF Connectors
PCT and DC Connectors
Wires & Heat Shrink
FFC, FPC, Berg connectors
Nextion
Segment
Seedstudio
Waveshare
E Bike Batteries
E bike Battery Case
E bike Connectors
E bike Display
E bike Kit
E bike Motors & Controllers
Electronics Accessories
Mechanical Accessories
Display
Cameras