![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-6-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-6-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-5-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-5-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-4-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-4-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-3-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-3-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-2-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-2-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-1-768x768-1-150x150.webp)
![](https://robotwala.co.in/wp-content/uploads/2023/07/Current-and-Voltage-Detection-Module-1-768x768-1-150x150.webp)
This module can be used to test the current and voltage. The principle of voltage test based on the principle of resistive voltage divider design can make the red terminal connector input voltage to 5 times smaller for Arduino analog input voltages up to 5 v, the voltage detection module input voltage not greater than 5Vx5=25V (if using 3.3V systems, input voltage not greater than 3.3Vx5=16.5V).
Hurry and get discounts on all Apple devices up to 20%
Sale_coupon_15
₹199.00 ₹179.00
Inclusive of GST
To pick up today
Free
Our courier will deliver to the specified address
3-4 Days
139
courier will deliver to the specified address
5-7 Days
90
Payment Methods:
This module can be used to test the current and voltage. The principle of voltage test based on the principle of resistive voltage divider design can make the red terminal connector input voltage to 5 times smaller for Arduino analog input voltages up to 5 v, the voltage detection module input voltage not greater than 5Vx5=25V (if using 3.3V systems, input voltage not greater than 3.3Vx5=16.5V).
For Arduino AVR chips have 10-bit AD, so this module simulates a resolution of 0.00489V (5V/1023), so the minimum voltage of the input voltage detection module is 0.00489Vx5=0.02445V. The MAX471 chip on the board used to test the consumed current of the load
VT: voltage detection pin, the detected voltage is 1/5 of the input voltage
AT: Current Detection Pin
GND: Connect to Arduino GND
VOUT/VIN: VOUT=VIN
1 x Current and Voltage Detection Module Arduino Compatible.
Test Voltage range: DC3 – 25V (for Arduino work on 5V) or DC3 – 16.5V (for Arduino work on 3.3V)
Test Current range: DC0 – 3A PCB
Size (LxWxH)mm : 22Â x 21 x 7
Operating voltage | 2.5 3.0V |
Pixel Resolution | 0.3MP |
Photosensitive array | 640 x 480 |
Optical Size | 1.6 inch |
Angel of view | 67 degrees |
Maximum Frame Rate | 30fps VGA |
Sensitivity | 1.3V/(Lux-sec) |
Dormancy | Less than 20A |
Power consumption | 60mW/15fpsVGA YUV |
Temperature operation Range | -30 C ~ 70 C |
Pixel area | 3.6 x 3.6 m |
Signal to noise ratio (SNR) | 46 dB |
Dynamic range | 52 dB |
Test Voltage range(If i/p voltage 5V) |
DC 3 ~ 25 V |
---|---|
Test Voltage range(If i/p voltage 3.3V) |
DC 3 ~ 16.5 V |
Test Current range |
0 ~ 3A |
In stock
In stock
In stock
In stock
In stock
No account yet?
Create an Account
Reviews
Clear filtersThere are no reviews yet.